Do it yourself Applications
How to make a unique Ferris wheel advent calender
Advent calendars are an essential part of the Christmas season – they sweeten the wait for Christmas and bring a little joy every day. Why not try something different from the classic shop-bought chocolate version? Making your own advent calendar is becoming more and more popular, whether as a thoughtful gift for family and friends or as a festive decoration for your own home. A DIY advent calendar is always something magical and special. We’ll show you step by step how to create an extraordinary advent calendar in the shape of a Ferris wheel. You can fill and decorate the small gondolas however you like. Your advent calendar is guaranteed to be the highlight of the Christmas season.
What you’ll need for your project:
Material:
- bicycle wheel rim, 26 or 28 inch
- four wooden slats
- one wooden board
- 24 small plastic cups
- 24 M4 brass screws
- one threaded rod
- two cap nuts
- one copper rod
- fairy lights
- decorative fir branches
- cable ties
- permanent marker
Tools:
- Drill
- Cutting Machine
How to make a unique Ferris wheel advent calendar – step-by-step guide
Step 1
Planning
Preparation and planning are key to success. First, decide on a bicycle rim – we went for a 28-inch one. When buying cups for the gondolas, make sure they aren’t too big. To check that they won’t bump into each other when the wheel turns, place the 24 cups around the rim first. We used cups that are 5 cm high and 5 cm wide.
Step 2
Preparation
Start by preparing the rim and the frame. You’ll need 24 holes in the rim where the gondolas will later be attached. Mark 24 drill points, each 8 cm apart. Drill the holes using a 3 mm bit, then cut an M4 thread into each one. Drill a 4.5 mm hole in each plastic cup as well. Next, cut and prepare the frame from four identical wooden slats. It’s important that there’s a gap of around 3 to 4 cm between the baseboard and the rim once the gondolas are attached. All dimensions can also be found in our sketch!
Step 3
Cleaning the parts
Once all preparations are done, clean each part. Use WEICON Surface Cleaner to wipe down the rim and the 24 cups. The cleaner is ideal for pre-treating bonding surfaces and reliably removes dirt and grease from materials such as metal, glass, ceramic and plastic.
Step 4
Bonding the frame
Now let’s start building or bonding the frame. Glue two wooden slats together at the top using WEICON VA 300 Cyanoacrylate Adhesive. This instant adhesive works especially well on absorbent and porous materials such as wood. Because the adhesive takes a bit longer to cure, use WEICON CA Activator to speed up the process. This activator is perfect for our cyanoacrylate adhesives. First, we apply the activator to one side and then use the adhesive on the other side. Next, drill a hole in each outer frame piece for the threaded rod. Finally, glue the two outer frame parts onto the wooden baseboard.
Step 5
Spraying the advent calendar
To give your advent calendar a festive finish, spray the rim, cups, screws and frame in Christmas colours. We used two of our products: WEICON Brass Spray and WEICON Copper Spray.
Both sprays are used to protect and enhance the appearance of metal parts. Shake the cans for about two minutes before use. Then apply the spray in slow, even strokes to each part.
This is how we divided up the colours – but, of course, you can decide for yourself which parts to spray in which colour:
- Brass Spray: rim, 24 screws, two cap nuts and 12 cups
- Copper Spray: frame, copper rod and 12 cups Let all parts dry for around ten minutes.
Step 6
Attaching the rim and cups
Now the advent calendar starts to take shape – time to put everything together. First, hang the rim in the frame. Thread the rod through the rim and copper rod, then insert it into the holes in the frame. Screw the two cap nuts onto the ends of the rod on the outside of the frame. Once the rim is secure, attach the 24 cups. Don’t screw them on too tightly so they can still move freely when the wheel turns.
Step 7
Adding Christmas decorations
To finish, we added fairy lights and some fir branches. Thread the lights through the spokes of the wheel and attach the battery pack in the middle using cable ties. This way, you can easily reach it to change the batteries. To disguise the battery pack, decorate it with a bit of fir greenery. Now it’s time to fill your advent calendar however you wish. We hope you have lots of fun and wish you a wonderful festive season!
Step-by-Step Video Tutorial
-
Installing a key safe - this is how it's done!You probably own multiple important keys – otherwise, you most likely wouldn’t have purchased a safe to store them. Now you would like to install your key safe, but you have no idea how to? Then this blog post is just right for you! We’ll explain to you how to attach your key safe securely to a suitable wall – in a few simple steps.Read the article now -
Epoxy Resin Shelf I DIY Crafting InstructionsYou like unique pieces of furniture made of epoxy resin and wood and want to do your own epoxy resin DIY project? Then you’ve come to the right place! We’ll show you how to make your own small epoxy resin shelf with these DIY instructions. In our opinion, a great idea that is also suitable for “epoxy resin beginners”.Read the article now -
Lining an old staircase with laminateIf the staircase is past its prime and the stairs are worn out, a staircase renovation makes sense. Sounds expensive? It doesn’t have to be. The cost-efficient solution for a new, fresh look: lining the old staircase with laminate! With the right adhesive and this instruction, I will show the DIY enthusiasts among you how it’s down.Read the article now